Changing table a la Vika Amon

Materials: Ikea desk Vika Amon, 2 foambars, 3 masonite boards, 8 screws, 4 wooden leg extensions, 4 m6 nuts and bolts, optional pads for wooden legs

Description: 1. Fasten masonite boards on three sides of the table with screws.
2. place the mat snugly in the middle.
3. Start changing diapers.

4. After 2 weeks or whenever your back say no to the awkward back position. Get the leg extensions from somewhere, mount it carefully using a size 6 metal drill and a wrench or size 10 key and polygrip.
5. Most important, keep smiling!

~ jonas, Zug, Switzerland

Read More »

A Twin Size Headboard for Less than $10

Materials: Vika Amon (Article No 500.711.70)

Description: I was looking to buy a simple headboard for a twin bed for use with a standard metal frame. However, it was difficult to find one without having to buy an entire bed and footboard. I wanted to avoid the footboard especially since the room I was working in was very small and didn'€™t want to spend a lot.

The Vika Amon table top measures 39 3/8"€ by 23 5/8"€ by 1 3/8"€ thick. The 39 3/8"€ table top is almost exactly the width of a twin bed, so I turned the table top sideways and used it as a headboard. I used the Vika Amon in white (Article No 500.711.70) which lists for only $5.99. It is also available in the same size in the black/brown finish for $10.99 as Article No. 002.098.39.

I bought the nuts, washers and bolts at Lowes for less than $3.00. It worked great and with the hardware cost less than $10.00 for everything.

The headboard is not very high (only about 6"€-8"€ above the surface of the mattress but it is enough to keep the pillows from sliding down. It also provides a good place to mount one of IKEA's flexible reading lamps like the Tived LED flexible stalk light for reading in bed.

Materials:
- Vika Amon: White (Article No. 500.711.70, $5.99) or Black/Brown(No. 002.098.39, $10.99)
- Four 1/4 by 2"€ long hex head bolts (cap screws)
- Eight 1/4" fender washers (large diameter w/small hole)
- Four 1/4" nuts (I used nylon insert lock nuts for vibration resistance)
Tools:
- 1/4" drill bit and drill
- Two wrenches, 7/16"€

Directions:

1. Trace Holes: You will need to drill four holes in the Vika Amon for the bolts to pass through. In order to place the holes appropriately, I placed the Vika Amon flat on the floor and stood the metal bed frame up on it. Place the bottom edge of the bedframe near the bottom edge of the Vika Amon so that the lower hole is about 1/2 - 3/4"€ away from the edge. I traced the openings in the metal bedframe onto the Vika Amon with a Sharpie so that I would be sure the drill in the right places.

2. Drill: Remove the bedframe, put the Vika Amon on a work surface and drill the four 1/4" holes in the appropriate places. I drilled fairly close to the edge to take maximum advantage of the internal frame near the edges in the otherwise hollow tabletop.

3. Bolt: Put the bolts in from the back of the Vika Amon (wall side) using a large diameter fender washer to spread the load across the relatively thin surface material of the Vika Amon. Putting the bolts in from the wall side will also prevent the bolts from protruding and perhaps damaging the wall surface. Slide the bolts through the openings in the metal bed frame and again using a large diameter fender washer, put on the nuts and tighten. Be careful not to overtighten and crush the surface. This is another advantage to using the nylon insert lock nuts.

~ Rich M, San Diego

Read More »

Work desk made out of 3 Expedit shelving units

Materials: 2 x Expedit 2x2 unit, 1 x Expedit 4x2 unit, 1 x Vika Amon 150x74cm tabletop

Description: Before this hack, my Ikea dining table was my work desk and littered with papers and stuff.

To start fresh in 2013, I decided to put a dedicated work desk in my home.

However I also needed enough storage space for my papers, printers and other stuff.

When I had a look at the desks with storage which Ikea sold, they were just not practical enough for me.


The Vika Amon tabletop which Ikea sells was 150cm wide and 74cm deep, perfect for what I needed!

As legs I have used the Expedit 2x2 units, however without the thick top shelf of them. Otherwise the table top surface would be to high, approx 82,5cm.

Without the thick top shelve it was only 77,5cm high in total. Perfect height for a desk.

The big problem with using the tabletop on the Expedit was that the units are 79cm deep and the desk only 74cm. So this would leave less then 1 cm on the back for the tabletop to rest on the Expedit vertical shelf. This was solved by mounting L brackets to support the tabletop (and painted the brackets black), and wooden pegs for the thin vertical shelf.

Please note that when you do remove the thick top shelf of the Expedit, paint the top surface black to not see the wood when you mount the table top to it (I did not do this yet when I took the photos).

To provide even more storage, an Expedit 4x2 unit was placed on the right side of the desk. And here also the bottom thick shelf was left out for a cleaner look.

To make place for my 2 printers, I have moved 2 vertical boards a bit and all was secured with wooden pegs

The unit is mounted with long brackets on the back (no L brackets used here), and drilled some holes for wooden pegs so that the sides of the unit cannot move.

All cables for the printers are fed through the hollow side walls of the large unit, as we all love invisible cables! Also a mountable power outlet was placed out of view.

It all looks very clean now, and almost as it is a standard package which you can buy.

(I still have to mount the doors on my Besta tv unit, please ignore those ;) )

~ Jeroen Zelle, Aalsmeer, The Netherlands

Read More »

Vika Desk with Billy Surround

Materials: Vika Amon desk with Adils legs and Alex drawers, with 2x Billy Height Extensions, Billy Wall Shelf & Capita legs

Description: My old desk had been falling apart for quite some time, and I had been looking for a new one for just as long. I like my desks to have plenty of storage, making good use of the wasted space above the monitor. Sadly I couldn't find a desk that met my needs, so I decided to take matters in to my own hand.

I had seen desks that had been hacked, and looked in to creating my first hack to replace the old desk. I bought the boxes and put them together to create my new desk with more than enough storage, even for a horder like me.


I first created an unhacked Vika Amons desk using three legs and an Alex Drawer unit. I then made the two Billy Height extension units, and fixed them securely using the provided screws to the top of the desk, drilling holes as needed. I left a 1cm gap between the table edge and the height extenders, for looks.

I then made the Billy Wall Shelf, being sure not to use the wallmounts provided, and attached Capita 21cm legs in all four corners. An alternative is to use the Capita Brackets instead of the legs, but the weight of the wallshelf is more than enough to keep it secure and steady when standing on top of the Billy Towers.

For a first time hacker, this is a simple hack which is just a matter of drilling a few holes where needed. It gives plenty of room between the billy units for a monitor and speakers can be housed atop them.

~ Fudce, Birmingham, UK

Read More »

Toddler desks

Materials: Vika Amon, Molger

Description: We needed two desks for our toddler girls -- they were 2 and 4 at the time -- but no one makes anything simple at the right height. I didn't want anything with too much bulk to it.

This hack is really simple -- just use the Vika Amon top. It's $5.99, easy to clean, and cheap enough to even be disposable. Ours have been great for 2 years, the kids even climb on them.

After searching the entire web site for hours, I finally found a great option for legs -- the Molger sink base. These are typically used to support a porcelain sink. They are the right height. They were about $20 for a set of 2. I mounted them with simple wood screws. Unfortunately, Ikea no longer sells these legs. Instead they offer the Godmorgon steel post leg, which is a good alternative. These legs are $10 each, which is a little more pricey.

We added storage below with Trofast - the wall storage frame for $24.99.

The best part about these desks is that they are at a great toddler height, and they work well with the Mammut stools shown.

~ AdamB

Read More »

Spicing up the bedroom with a killer headboard

Materials: 4 x VIKA AMON high gloss RED (150 x 75 cm), 2 x wall shelf (similar to LACK, but from local HW supply since I wanted them in high gloss), battens from local HW supply, LED light strips (not IKEA since sold out on day of my visit), 4 x wall outlets, 2 x light switches, various screws and hinges

Description: My wife and I wanted to spice up our fairly boring bedroom in our newly built house and after long considerations chose to create a killer headboard from IKEA parts.

Here is how we did it:

1) Lay down all 4 VIKA AMON table tops on the floor next to each others. Be careful not to scratch the high gloss surface. We used the wrapping material as support.

2) Attach each VIKA AMON table top to the next using flat hinges. Use the wall as support, so the end of the table tops align perfectly (will be the top of the headboard)

3) Create a frame of the battens and mount it to the VIKA AMON table tops using bracketing hinges. We allowed 25 cm free space around, so the battens wouldn't be visible after being attached to the wall.

4) Create a wall support mechanism by using 2 short pieces of batten on each side. The final headboard will be resting on the floor, so this is only to keep it flat against the wall in the upper part.

5) Month the either pieces on the wall accordingly. Use a measure to ensure right positioning.

6) Drill holes in the VIKA AMONs to allow the wall outlets to be fed from the back (WARNING! If you're not a trained electrician, don't do this on your own). We created 4 holes, since we have elevation beds that needs power too and we wanted those wire not to be too visible. Careful when drilling, so you don't scratch the high gloss surface. We used tape to support this, which could easily be removed afterwards.

7) Connect all wall outlets and light switches.
8) Attached the LED stripes directly on the batten frame at the back. The version we got glued directly on.

9) Attach the shelves on each side as described in the instructions (no hacking here).

10) Mount the headboard on the wall and enjoy ;-)

~ Soeren Juul Schroeder, Denmark

Read More »

Vika Amon, Hacked

Materials: Vika Amon and Capita Legs

Description: Step 1: Search tirelessly over the internet for a coffee table that will be just right for your space.

Step 2:Fail at step 1

Step 3:Browse Ikea countertops looking for a nice wood selection.

Step 4: Browse legs and determine that straight legs are boring.

Step 5: Notice the Vika Amon table top is 1/4 the price of the counter tops.

Step 6: Uniquely marry the Viko Amon Table top and the slanted Capita legs into a unique coffee table.

When joining the legs, drill a hole straight through the bottom table top.

The thickness of the table pairs perfectly with the length of the "ready-rod" which allows you to sandwich the bottom shelf by joining the legs together through the shelf. Don't over tighten as you might scratch the table top, or if you drilled in an area without backing, crack it even.

I recommend drilling where there is backing, but in order to get a funky look you may have to offset it a bit.

~ Shane, Vancouver Canada

Read More »

VIKA ports from the noise storm

Materials: VIKA AMON Desktops, aluminum angle iron, good cider

Description: Open offices are awesome. Open offices are loud. Loud is often fun, but sometimes bad.

My company, Sharethrough, loves us an open office. We love the collaboration, the misused office supplies flying from desk to desk, and we love working together to make cool things.

But sometimes you need some quiet. We usually don't want or need quiet or isolation enough to move our desk into some corner, we just need a space to bang through some work in a quiet environment where we can spend an hour or a day away from the open office cacophony.

Enter the Quiet Desk. One of our founders suggested making some desks that were like study hall in college, with some visual division and quiet from the rest of the office. Not wanting to do a lot of shop-building, I decided to build as much of it as possible from off-the-shelf Ikea parts.

The build is pretty straightforward. The dividers are 59" x 29.5" VIKA AMON desktops in gloss white. there are three of them standing on edge between/on the end of the worksurfaces. I bought hammer-on furniture glides at my local hardware store to keep the edges of the dividers slightly off the floor.

The work surfaces are VIKA AMON 39.375" x 29.375" desktops in Black-Brown. They're joined to the dividers with 1" Aluminum angle Iron (also from the local hardware store) which has been cut to 29.25" in length to form a side bracket. This length lets both ends of the bracket connect to the blocking in the dividers, providing better support for the work surface. For added strength, I also epoxied the bracket to the dividers.

Finally, I added two additional VIKA AMON 39.375" x 29.375" desktops in plain white to the lower-backs of the desks. This will provide privacy if we ever take these away from the walls, but most importantly, they greatly strengthen the overall piece, guarding against side-to-side racking that we'd otherwise get. These were joined to the dividers using brackets made from the waste in cutting the work surface brackets from the original 48" lengths the aluminum came in.

All the assembly was done using 1" lath screws (nice wide heads, no need for washers), being really really careful not to overtighten them into the particleboard blocking in the VIKA desktops.

Finally, I wired and zip-tied a power adapter and a set of headphones into each desk, so you can take your laptop with you, and get your jam on. I used some leftover mounting posts from a SIGNUM cable management basket, together with a 5/8 fender washer to make a handy storage place for the 'phones.

It took about 45min and 1.5 Hornsby's Amber Ciders to cut and drill the brackets, then about 2hrs total to assemble all the bits.

Happy Quiet Place!

~ Troy, San Francisco, CA

Read More »

Vika Amon-Galant 1m high standing table

Materials: VIKA AMON 150x75cm table top, Galant 120x60cm table base & 4 Angle legs, 2 x BESTÅ leg packs (2 per pack, total of 4), 2 pieces of wood (600mm x 65mm x 18mm each or similar), 4 x M8 30mm hex head bolts, 4 x M8 50mm hex head bolts, 4 x M8 washers, drill & drill bits, 16+ x 30-40mm long wood screws, optionally add EKBY shelf with EKBY TÖRE brackets

Description: The idea came about as we wanted a standing table ~1m high, and on arriving at Ikea found out that the VIKA BYSKE legs (that go to 107cm high) are currently recalled. According to the store, it was a world wide recall. We had already decided we wanted something more than 60cm deep, which w as how we decided on the VIKA AMON table top (75cm deep).

Stability was important, so I put my thinking cap on and came up with what you see. The BESTÅ legs were a last minute inspiration walking around the self-service furniture area on the way to the checkout. Originally I was going to use some wooden blocks and M8 threaded rod (which I have lots of for other reasons), but when I saw the BESTÅ legs, I just knew they'd be perfect and that I had to use them, despite it being slightly more expensive. Sure it's not the cheapest standing table, but we're quite happy with it.


Step 1: Drill the corner holes in the GALANT frame all the way through (8-9mm dia). Clamp one piece of wood onto the frame where the holes are and centre it so the same amount is sticking out each side. Drill both holes all the way through the timber (8mm dia). Repeat for the other side and piece of wood. They should be identical anyway, but I did it this way in case I was slightly off-centre with one side.

Step 2: As I couldn't find M8 countersink screws on a Sunday, I improvised. Countersink the holes using a 13mm dia drill to approximately the height of the hex head for the M8 30mm bolts. Put the wood on something stable with a hole in it (I used half a brick I had lying around), and put the M8 30mm bolt through the hole. Hit the bolt head with a hammer till the head of the bolt is flush with the timber. Repeat for remaining timber holes & M8 30mm bolts.

Step 3. Unscrew the plastic feet from the BESTÅ legs, just leaving the Aluminium piece in the centre. Screw these onto the M8 30mm bolt threads sticking out of the timber pieces. Using the M8 50mm bolts and the M8 washers, screw the GALANT frame into the other side of the BESTÅ legs (drilled hole side goes to the BESTÅ legs).

Step 4: Invert the VIKA AMON table top, and place the new GALANT frame assembly on it, timber down. Centre the frame assembly on the desktop and secure with the wood screws (I countersunk mine, as they were a little short). If you drill pilot holes for the screws, make sure they are well undersized, so the screws bite into underside of the VIKA AMON table top. I used 4 screws per corner (for a total of 16), but may add more later (possibly between the BESTÅ legs).

Step 5: Add the legs, adjust each to the same height, and then stand the table up. You're done!

At full leg extension we measured the surface of our table at 101cm. We also garnished ours with a EKBY shelf mounted with EKBY TÖRE brackets (matched well with the VIKA AMON series tabletop).

Notes:
1. At full extension, the legs sit wider than the table top (front to back). This means it doesn't quite sit up against the wall, but this isn't an issue for us and we prefer the stability of the angled legs.
2. If I feel the stability isn't quite there, I'll go buy another pack of BESTÅ legs and put them between the existing ones (front to back), and put them on the centre of the frame so the welds on the GALANT frame edge are carrying less weight.
3. Another possibility is to use longer pieces of wood and run the wooden supports that attach to the table top from left to right rather than front to rear. This would provide ample places to screw the wood to the table all over (eg: nearer the existing leg holes in the VIKA AMON table top).

~ Cefiar, Melbourne, Australia

Read More »

Easy made conference table

Materials: 3x Vika Amon tabletops 1x Galant table legs (only the table legs not the tabletop), 1x Chipboard (it should be a bit smaller than the size of the three tabletops)

Description: Why are we hacking? We are a new company in Denmark and needed some furniture to fill our office. As a entrepreneurial company it was not necessary to have expensive designer furniture filling up our office, however, we would like some good looking furniture that fulfills our needs. Where else to go but IKEA!

What to do?
1. The chipboard was put underneath the 3 tabletops and screwed together.
2. Afterwards we screwed the table legs to both sides/ends of the tabletops.
3. Voila! It turns into our new conference table.

See more of the Vika Amon conference table.

~ Stine Olesen, Compell, Denmark

Read More »

The tiny kitchen island

Materials: Expedit 2x2, Vika Amon, Expedit drawers and legs from other shop

Description: I have a small area in my kitchen/livingroom so I decided to do this by using Ikea stuff which are cheap and easy to work with. Those legs I bought somewhere else. I'm very satisfied :)

~ Sabina, Tampere Finland

Read More »

TriFecta Computer Desk

Materials: (2) VIKA AMON - Table top, white (Length: 39.3/8" x Width: 23.5/8") / (2) VIKA ADILS - Leg, white (non-adjustable) / (1) ANTONIUS - Shelf, white / (4) EKBY STÖDIS - Bracket, white / (1) LEDBERG -3-piece light strip set, white [optional added feature]

Description: This computer desk was completed using two table tops. One table top is used as the flat horizontal surface, the other as the back support, or "uni-leg", turned vertical length side upright.

In the front are 2 table legs. Next, fastening the two "table tops" together are two brackets. Also, two more are used to support the smaller top shelf, which can be used for a Computer Monitor, Books or Software!

Lastly, and optional, a 3 piece LED light strip was added. This added lighting feature is secured to the small top shelf towards the front!

*Components:

(2) VIKA AMON - Table top, white (Length: 39.3/8" x Width: 23.5/8")

(2) VIKA ADILS - Leg, white (non-adjustable)

(1) ANTONIUS - Shelf, white

(4) EKBY STODIS - Bracket, white

(1) LEDBERG - 3-piece light strip set, white [optional added feature]

I hope you enjoyed this "trifecta computer table, and if you choose to make this or a variation thereof, have fun! Remember we're only limited by our imagination & budgets!

~ UNtamED ©, Seattle, WA

Read More »

Budget King-sized headboard with luggage storage

Materials: 
2 - 39" Vika Amon table tops (black-brown)
1 - 74" Lack wall shelf with hidden hardware (black-brown
4 - metal "patching" brackets
1 to 3 - 8" X 10" L-shaped wall brackets
2 - 1.5" X 1.5" wood posts
1 - 1" X 4" board

Assorted Screws:
lathe screws
wood screws
screws with drywall anchors

Tools:
Drill with drill bits and screwdriver bits
level
hammer
saw

Description: This hack was inspired by post "headboard fit for a King-sized bed."


1. Lay the two table-tops face down and align them side-by-side, creating a 78" long table-top.

2. Use the metal patching brackets to fasten the two table-tops together. Space the brackets over the lower 4/5 of the seam. Use the lathe screws to connect the brackets to the table-tops.
3. Center the hardware for the Lack Shelf on the seam along the top edge of the back of the table-top. The lower screw-holes will be above the hollow- cardboard filled center of the table-tops so use drywall anchor screws for those fastenings. Some of the holes will be on the solid outer border of the table-top and wood screws will work there.

4. Place the Lack shelf on its hardware and secure in place with the provided screws.
5. Cut the two 1.5" X 1.5" posts to the length necessary to achieve the desired height. I needed a 50" high headboard, so my posts were about 26" long.
6. Cut the 1" X 4" to a length that is about 12" longer than the posts.
7. Aligning the bottom of the posts with the bottom of the 1" X 4" board and centering the posts on the 1" X 4" board, fasten together using wood screws or deck screws. This will create a t-shaped leg to support most of the headboard's weight.

8. Fasten the legs to the headboard. Anchor screws will be needed for some of the fastening and wood screws will be need for the rest of the fastening.
9. Install the L-brackets on the wall to support the the Lack shelf and the rest of the headboard's weight.

10. Place headboard and attach to wall-bracket.

~ Chelsea, Oklahoma City, OK

Read More »

VIKA does a handstand

Materials: one VIKA ADLIS leg, orphaned umbrella base, nut, washer, adhesive cement, small screw bit, small jig saw blade or heavy duty knife that cuts thick plastic

Description: I was resigned that until James Dyson consulted with the outdoor furnishings industry, there would never be stable, aesthetically decent, tall-enough, well-fitting and long-lasting umbrella stand. And even if he did, it would take a decade to come to market and be priced at $400.

Found a $40 pole and base combo at a drug store that was 1/2 OK = base of solid granite. But the pole was wobbly, short, too large in diameter and with too anemic a screw to tighten the umbrella properly and permanently.

Then I remembered my $3.50 VIKA table legs from IKEA!


1. Vika table legs come with a removable rubber/plastic "stopper" on the bottom.

2. Remove stopper; place on a drill-able work surface with flat side down. Slowly drill a hole through center of stopper to gain access for saw or knife blade. Carefully cut out (so as not to split the stopper) a hole a tiny bit larger than your umbrella's pole.

3. Glue stopper back into pole.

4. Match a nut and washer sized to VIKA's screw-in top, which will be the bottom of the pole. Screw pole into stand. I lucked out, but you may have to add an intermediary disc or washer on top of the base, if its hole is larger than VIKA's diameter.

5. Donate VIKA's screw plate to a Habitat for Humanity ReStore.

~ John, Left Coast USA

Read More »