• Home
  • Contact
  • Privacy Policy
  • Disclaimer
  • DCMA
  • Terms
  • cancer science review

    A Creative Exercise Using RUSCH Clocks

    Posted by Unknown Posted on 11:37 AM with No comments

    Materials: RUSCH clocks, anything to decorate the clocks with (spray paint, fabric, dollar store trays, etc.)

    Description: Description: The RUSCH clocks are really cheap here - in USD $0.84. I wanted to see what sort of ideas I could come up with when hacking the look and design - so I ended up buying 5 of them.

    My first experiments were based on trying to change the look of the whole clock - like spray painting the frame black. But anyone who has seen one of these clocks would know what I just did. So my attention went to hacking the round plastic cover. This way the new clock designs wouldn't look like the original RUSCH design.



    For three out of the five clocks (The Black Beast, White on White, and Dressed Up) I ended up using the round plastic cover as a base. Two were spray painted, another covered up with fabric. For the Black Beast I cut up the seconds hand to create the number locations.

    I didn't want the seconds hand on any of the clocks so I cut off the stems, just to keep the round tab to cover the hole.


    Next up is the Double Dose clock. Instead of using the round plastic cover as the base I glued cardboard to the back of an IKEA MARIT dinner table mat.


    The last clock, Horizon, used a dollar store serving tray as the base. Half of it was spray painted black, the other half white, to give it a more abstract design. All of the spray painting, including the painting of the first two clocks, were done inside of an IKEA shopping bag (so the spray paint doesn't go everywhere).



    To see more pictures of the clock hacks, click here.

    ~ Jacob, Malaysia
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    iCork Clock

    Posted by Unknown Posted on 11:11 AM with No comments

    Materials: Kvissle, iHome, hot glue gun, drywall screws, Drill, magnets

    Description: I first got the idea from the Kvissle Boom Box Hack.

    I took my old iHome apart. The speakers didn't work and the some of the buttons were malfunctioning. So I got rid of all the unnecessary components.

    I traced the clock screen onto the back of the cork top and cut it out with an Xacto knife, then hot glued it to the cork. The cork flaked a bit in some areas so if I redo it I might try another technique.



    I positioned the circuit board and hot glued the button and nobs components directly to the inside of the box.

    The top is held on by magnets which were hot glued as well.

    The power cord was routed through the side hole of the box and i secured it to the wall using screws through the foam pad holes.

    ~ Mason R, California
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Miniature Car Display

    Posted by Unknown Posted on 12:08 PM with No comments

    Materials: Ribba X 9

    Description: Wanted a cool display for my collection of Miniature Coal Made Cars.

    Connected 7 horizontal RIBBA's with 2 RIBBA's, one on each side.

    You can play with the height/distance to fit your needs

    ~ Saar Machtinger, Israel
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Hacker help: How to make a lamp from x-rays?

    Posted by Unknown Posted on 7:42 AM with No comments

    Materials: ?

    Description: I want to make a wall lamp out of my x-rays of my head (cat-scans). I think the idea is pretty cool, but I am stuck on how to make it happen..

    Any ideas?

    ~ Hege_Norway, Norway

    Hege, 
    You can try using the Gyllen lamp (photo above) and personalise it like how Damian did it. ~ Jules

    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Shadow box thing

    Posted by Unknown Posted on 4:21 AM with No comments

    Materials: 50 cm Ribba frame, piece of 3mm MDF, 2 cans of flat white spray paint

    Description: 1. I removed the glass from the frame (but you could keep it if you wanted). I cut a piece of MDF to fit the frame, for a back, and painted it white.

    2. I measured my largest ornament (it was the yellow horse on the bottom row) to get the size of the squares. I ruled the squares onto the MDF.

    3. I sawed 3 cm strips of MDF and painted them white, including their front edges.

    4. I cut them to size and glued them in place to make little shelves.

    5. I put the frame back together. It was fiddly, but easy enough, and I'm happy!

    ~ judith, australia
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Ikea Message Center on the Cheap!

    Posted by Unknown Posted on 11:50 AM with No comments

    Materials: A cabinet door rescued from Salvage

    Description: I happened across the AS-IS section of IKEA and found a lovely cabinet front. I was so happy as I lugged the $2.00 board to my cart. Probably too happy as I got weird looks from other customers. Crafters can attest to you though, Ikea'€™s AS-IS section is DIY Gold!

    That $2.00 board with a little DIY love is now our family message center. If I was bright I would have taken a before picture but alas my happiness got in the way of my organization. Sorry.

    We painted the cabinet front white to make it brighter. We then cut a piece of sheet metal to fit in the opening so that it would be magnetic.

    I like color so we made the sheet metal a happy yellow color. We then made a design using blue painters tape and painted the rest white!

    We then drilled three holes and installed nobs to hang coats on. I love the knobs at Anthropologie but I have founded if you really look that Hobby Lobby has similar ones for a fraction of the price.

    Now it is hung in the hall using picture hangers and it holds coats, school forms, and a calendar from Hello Cuteness where I write our monthly menu plans!

    See more of the Ikea door message board.

    ~ Tiffany S., Southwestern United States
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Sacrifice Skovel and Rusch on the altar of Noir

    Posted by Unknown Posted on 4:39 AM with No comments

    Materials: Skovel, Rusch

    Description: I used the Skovel wall clock to replicate Kirika's pocket watch (not to scale, obviously) from the 2001 TV series Noir. An extra Rush was sacrificed for the clockwork of the off-center seconds hand.

    I was inspired to make this geekish hack by the 10th anniversary of the Noir DVD release, and the availability of the eminently hackable Skovel clock, which is relatively cheap, simple and straightforward in its assembly, yet with a steel and glass body.

    Removing 4 screws is enough to take off the glass. I carefully lifted the hands off of the clockwork with a fork. After this, unscrewing a single nut separates the clockwork from the body.



    I removed the paper clockface with the aid of heat from a hairdryer. In retrospect I should have simply pasted the new face over it, because the sticky goo that remained was nearly impossible to get rid of.

    I created the new clockface in a graphics program, printed it out on A3 paper and glued it on the body after drilling the hole for the seconds hand.

    Because the seconds hand revolves under the minutes and hours, I had to make sure it didn't protrude too high above the clockface. I therefore used a spacer (made of scrap wood) between the back of the clock and the Rusch mechanism. To limit the size needed for the hole, I removed the hour and minute axles from the Rusch mechanism, leaving only the parts needed for the seconds. Both the mechanism and the spacer are held in place by 2-sided adhesive tape.

    The new clock hands were cut from paper card stock, and glued on the cut-off hands of the Skovel (and the seconds hand of the Rusch). Finally I added some accents with silver-colored marker.

    In all, it took only a couple of hours to turn the rather unexciting Skovel into the envy of all Noir fans.

    ~ Eli, A place forgotten by time
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Broder Shelf - Modern Steel Wall in 30 minutes!

    Posted by Unknown Posted on 9:22 AM with No comments

    Materials: Broder galvanized steel shelf X 10, drywall inserts, floral wire, drywall screws, screw hooks, measuring tape, level.

    Description: This hack was inspired by my recent trip to the Ikea As-Is department. As seen in the images, I had an awkward shaped sloped wall behind my couch. This is problematic because my large canvas could not be centered! The goal: create a large modern metal wall that will still allow light to come through- oh, and NO construction!

    Step 1- purchase 10 galvanized steel Broder shelves. (I got mine in the As-Is department for 1$ each! total steal!)



    Step 2- (2 minutes) Measure your wall! These shelves measure 46" X 14.5". The goal was to cover the entire wall- so I measured accordingly and purchased what I needed to fill the wall. Lucky for me, the width and length were perfect for my space.

    Step 3- (8 minutes) I drilled two holes on the ceiling above the awkward slant so I could descend my shelves (see image). I recommend using drywall inserts because these shelves can get heavy. I then screwed in two hooks, allowing me to hang the shelves using floral wire.

    Step 4- (20 minutes) Hang your shelves! USE A LEVEL while hanging so all the shelves line up. While hanging shelves in front of the awkward slant I continued to use floral wire to connect my shelves... Attaching the top shelf to my ceiling hooks, second shelf to top shelf, then third to second. After this I was able to actually put screws into the wall and just hang the shelves directly. Make sure that the shelves are equally spaced from each other while hanging using a measuring tape.

    Step 4- ADMIRE and ENJOY!

    TIP- galvanized steel has the tendency to yellow/dull over time... prevent this with a clear acrylic coating that can be purchased at your local hardware store.

    ~ Amber Richter, Orange County, CA
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    LACK table clock

    Posted by Unknown Posted on 7:16 AM with No comments

    Materials: LACK table and sticker clock

    Description: It is very simple, the clock is stuck in position and made the hole for the mechanism. And ready to hang.


    ~ Miguel, Madrid, Spain.
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Wood RUSCH clock

    Posted by Unknown Posted on 11:38 PM with No comments

    Materials: Rusch clock, a piece of wood, some varnish, a circular saw

    Description: I took a slice of wood, sand it and with a circular saw I cut the back of it very carefully to fit the mechanism of the Rusch clock. It's very difficult since the metal rod of the clock is not thick at all.


    I fixed the clock with two screws because it didn't work with glue.

    I wrote the numbers with a pyrograph.

    ~ Vincent, Versailles (France)
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Real computer in a picture frame

    Posted by Unknown Posted on 4:54 AM with No comments

    Materials: 1x Ribba frame (25x25x4,5cm), old laptop, sharp knife, black paint, some plywood (3mmx25cmx25cm)

    Description: Image you bought a new laptop, what to do with the old one?

    1. Disassemble the old laptop and make sure the motherboard fits in the 25x25cm frame.

    2. If it fits continue and remove necessary accessories from your laptop (I reused the power, LAN and USB connectors and the power switch). Now use the knife and cut out some holes for those connectors in the frame. Don't care about the small frame the secures the glass, we'll come to it later.

    3. Cut the plywood to 25x25cm and cut out the mounting points from the laptop case and glue them on to the plywood and install the motherboard.



    4. Buy some cables to connect the hard drives to the motherboard (I build my own cables)

    5. Find a good spot for a hard disk (or 2) in the frame and use some small metal hinges to install it. There should be some metal in the old laptop case, use that! Install the hard disks directly behind the glass so it will secure it.

    6. Put everything together hang it on the wall plug in the power and network cable and switch it on.

    ~ Marcus Goth, Sweden
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    LP RUSCH CLOCK

    Posted by Unknown Posted on 4:42 AM with No comments

    Photo: IKEA.com
    Materials: RUSCH wall clock, old vinyl record, glue gun, marker pen.

    Description: This is maybe the simplest hack yet,

    I bought RUSCH wall clock ($1.99) a while ago and planned to hack it later. Then later I bought some old vinyl record from a flea market for just ($1.00) a piece.

    First I started by removing the needles from the clock mechanism.

    After that, I stuck the clock mechanism behind the record's aperture using hot glue.



    The needles, I used a marker pen to colour it white so that they contrast with the vinyl record's colour.

    Then, I replaced the needles and just like that, it's finished. Like I said before, it is the simplest hack ever.

    ~ Anuar Nasiruddin, Malaysia
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    The frame hanger

    Posted by Unknown Posted on 11:55 AM with No comments

    Materials: Nyttja white frame 13x18, Lindsdal knob (or others)

    Description: I had 2 new frames (bought here in Italy just 3 euros/2 pieces) and 2 knobs (taken years ago from old wardrobes).

    One day I thought it was time to transform creatively these items into something useful and nice.... here you can see the result.



    STEPS

    1) drill at the middle of one side of the frame

    2) sand the frame until it gets an old, used look, by using different qualities of sandpaper

    3) screw the chosen knob; since the screw is created for the thickness of a wardrobe door, it will result longer: to fasten it to the frame, you should add one or more washers between

    4) then put a picture in, or better realize something with a retro-taste by choosing images on magazines (it's cheap and creative!)

    5) that's it! now you can hang by the wall your frame, and use it to hang neck-laces, bracelets, small scarfs or whatever you like!

    ~ serena, Milan, Italy
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    RIBBA clock hack

    Posted by Unknown Posted on 8:03 AM with No comments

    Materials: RIBBA frame

    Description: This hack is kinda easy, but it's also quite hard to describe as it is very specific to what you want to have in the end.

    The main steps are:
    - Get a RIBBA frame, one of those with the mat for three pictures
    - Get yourself three clockworks and possibly some watch hands you would like to use (make sure the hands fit the clock, otherwise use some superglue, to fix this ;-D). I used very quiet clockworks where the hand for the seconds never stops, looks better in my opinion.
    - Mark the final positions of your watch hands and drill holes at these positions (8 mm in my case) in the back of the frame
    - Prepare your clockworks: As every clockwork only uses one hand you have to cut the shafts or remove them at all. I used an scalpel and a wire cutter to strip mine down.
    - Put something under your clockworks before fixing them to the back of the frame. This helps to shorten the shafts even more, so you don't need to put very much under the mat in the end and you have no problem when using the glass where it is etc.


    Detail shot of a trimmed shaft

    - Design and print yourself a clock-face you like, glue it onto the back of the frame
    - Attach the watch hands and make sure they can run freely (you should check this earlier... ;-D)
    - Put something under the mat and place it in the right position (I cut a new mat from very high white, thick paper, as the original was too yellowish and had some bucklings right after buying)
    - Put everything back into the frame and enjoy your very unique and stylish clock

    Back of the frame with three mounted clockworks and one hand attached for testing purposes

    Some hints:
    - I wanted to use the same watch hand for all clockworks. This made it necessary to glue the hands onto the bases of other hands, so they could fit the shafts. Check this before you start and keep it in mind.
    - I also had to shorten my hands. Could be done with a scalpel and some super glue. Cut them at the "base", so nobody sees you shortened them...
    - When you put something under the clockworks it can happen, that they can become too deep and stick out of the frame. No problem for me, as I mounted the frame with the supplied hanger to my wall. Try to use clockworks with short shafts or trim the shafts as far down as possible. Be careful with trimming, sometimes the watch hands won't find in the end...

    I hope this hack can inspire some people to build interesting clocks.

    You can find some more information, and my clock face on the website I provided. The blog entry is in German. See more of the Ribba clock.

    ~ flomei, Germany
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    How to: Create a personalised picture with Lack and decal

    Posted by Unknown Posted on 8:56 AM with No comments

    Materials: Lack

    Description: I have an old LACK side table from IKEA that I no longer use.
    My sister-in-law wanted me to make her something personal and from the heart. That is when I realized that I could do something fun with the old table.

    1. I made a personal picture using Illustrator. I then send it to Parts of Sweden and let them print a furniture decal for me. They already have lovely decals so you don't have to know how to use Illustrator. You can choose between all the Disney motifs and many more.

    2. Wait for the furniture decal to be delivered to your home.
    3. Unscrew the legs.
    4. Clean the table with a rag.


    5. Remove the safety paper on the back of the sticker and place decal on the table.
    6. To see how to place the decal you can see a videoclip on Youtube here. The video has some Swedish text but hey, you´ll learn some Swedish at the same time.


    7. Attach whatever you can find at home that will make it easier for you to hang the picture on the wall. I bought this little metal thing and I am sorry to say that I do not know what it is called. However you attach it on the back of the picture.


    8. Now hang it on the wall. Tadaaaa!!!!!

    View more decals at Parts of Sweden.
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    Oh my deer!

    Posted by Unknown Posted on 8:31 AM with No comments

    Materials:
    Ung Drill, deer heat, wallpaper, spray paint, oval wooden plate

    Description: Make a contemporary deer.
    You don't need the glass and background of the Ung drill.
    I spray painted the Ung Drill. And made a new background out of plywood. Because the cardboard is not strong enough to hold the deer head.

    Glue the wallpaper on the plywood place in the frame and mount the deer head on the plywood. And it's finished.

    See more of the Ung Drill deer head.

    ~ Lynn Ruisendaal-Bosch, The netherlands
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON

    The "WHY DIDN'T I THINK OF THAT" hack

    Posted by Unknown Posted on 4:26 AM with No comments

    Materials: 2 Ekby Bjarnum brackets, 1 white Ekby Jarpen shelf (high gloss foil finish), circular saw or jig saw, coping saw, painters tape, round or square mirror of choice

    Description: The mirror sits out from the wall just a bit (cuz the frame on back) so I had to measure inwards on the shelf.

    Lay out the painters tape on the top surface of the shelf (this will allow a clean cut and prevent the finish from splintering).

    Mark out with pencil on the tape your dimensions/outline of the mirror (where you're going to cut).



    Set up and clamp your straight edge onto the shelf. (this is where your saws frame will ride against for the straight cut).

    If using a circular saw: you will have to do a plunge cut. (This is where you lower the saw down onto your pencil mark and into the wood.) Starting from the one end of your mark, you saw forward as normal and stop at the other end of your mark. Now you have a shelf with a straight cut through the length of it.

    Take your coping saw and cut from the outside towards the edge of your previous cut. And do the same for the other side. Now you have a nice recessed groove cut out of your fancy shelve.

    Remove your tape.

    *Easier and safer method is to use a jig-saw. I didn't have one at the time so I went the circular saw route. It requires more skill and patience than the jig-saw. I would recommend using the jig saw method if you have minimal wood-working skills. It's safer as well.

    **If you use the jig-saw method, drill a hole in each corner of your layout. (hole must be bigger than the width of the blade) That way, the jig-saw blade can pass through and start in the corner and make its way down the length of the shelf towards the other corner. Of course, you still use your straight edge so your jig-saws frame can follow that making a perfectly crisp and square cut.**

    Now to hang the shelf and mirror, you will need another set of hands. Assemble the shelving unit without the mirror and hold it up to the wall in your preferred location. Mark with pencil through the screw holes on each bracket. Now you can put your screw anchors into the drywall. (On mine I had one stud to screw into and the other was drywall. If possible, use the studs!) No anchors needed for the stud side though - only for drywall.

    Once the anchors are in, put the assembled shelving unit (without the mirror) up to the wall and screw it 1/2 to 3/4 of the way in. This will allow you to slip the mirror into place.

    Use construction adhesive on the mirror instead of double sided 3m tape (I went the DS tape route and it doesn't seem to stay too well). Have the other pair of hands put the mirror into place while you push the shelving unit into the wall. The groove you previously cut into the shelf will hold the weight of the mirror. Now hold it all, while you finishing screwing the rest of the way into the wall.

    That's it!! Let me know what you think.....


    Craig

    ~ Craig Arges, Kamloops, BC, CANADA
    Read More »
    FACEBOOK DIGG TWITTER GOOGLE+ LINTASKAN STUMBLEUPON
    Older Posts
    Powered by Blogger.

    Blog Archive

    • June (81)
    • July (100)
    • August (94)
    • September (74)
    • October (456)
    • November (275)
    • December (178)
    • January (257)
    • February (176)
    • March (185)
    • April (191)
    • May (207)
    • June (114)
    • July (223)
    • August (116)
    • September (71)
    • October (152)
    • November (49)
    | Contact | Privacy Policy | Disclaimer | DCMA | Terms |
    Copyright © 2013. cancer science review - All Rights Reserved
    Designed By Latest K-Pop News And bloggerspherepedia
    Proudly Powered By Blogger